مجموعة تكنولاب البهاء جروب

تحاليل وتنقية ومعالجة المياه
 
الرئيسيةالبوابةمكتبة الصورس .و .جبحـثالأعضاءالمجموعاتالتسجيلدخول
تنظيف وتطهير وغسيل واعادة تاهيل الخزانات


معمل تكنولاب البهاء جروب
 للتحاليل الكيميائية والطبية
والتشخيص بالنظائر المشعة
 للمخدرات والهرمونات والسموم
 وتحاليل المياه

مجموعة
تكنولاب البهاء جروب
لتصميم محطات الصرف الصناعى والصحى
لمعالجة مياه الصرف الصناعى والصحى
مجموعة تكنولاب البهاء جروب
المكتب الاستشارى العلمى
دراسات علمية كيميائية



معالجة الغلايات وانظمة البخار المكثف
معالجة ابراج التبريد المفتوحة
معالجة الشيللرات
مجموعة تكنولاب البهاء جروب
اسنشاريين
كيميائيين/طبيين/بكترولوجيين
عقيد دكتور
بهاء بدر الدين محمود
رئيس مجلس الادارة
استشاريون متخصصون فى مجال تحاليل وتنقية ومعالجة المياه
متخصصون فى تصنيع وتصميم كيماويات
معالجة الصرف الصناعى والصحى
حسب كل مشكلة كل على حدة
تصنيع وتحضير كيماويات معالجة المياه الصناعية
مؤتمرات/اجتماعات/محاضرات/فريق عمل متميز
صور من وحدات معالجة المياه


technolab el-bahaa group
TECHNOLAB EL-BAHAA GROUP
EGYPT
FOR
WATER
TREATMENT/PURIFICATION/ANALYSIS
CONSULTANTS
CHEMIST/PHYSICS/MICROBIOLIGIST
 
INDUSTRIAL WATER
WASTE WATER
DRINKING WATER
TANKS CLEANING
 
CHAIRMAN
COLONEL.DR
BAHAA BADR EL-DIN
0117156569
0129834104
0163793775
0174041455

 

 

 

تصميم وانشاء محطات صرف صناعى/waste water treatment plant design

technolab el-bahaa group
egypt
We are a consultants in water treatment with our chemicals as:-
Boiler water treatment chemicals
Condensated steam treatment chemicals
Oxygen scavenger treatment chemicals
Ph-adjustment treatment chemicals
Antiscale treatment chemicals
Anticorrosion treatment chemicals
Open cooling tower treatment chemicals
Chillers treatment chemicals
Waste water treatment chemicals
Drinking water purification chemicals
Swimming pool treatment chemicals
Fuel oil improver(mazote/solar/benzene)
technolab el-bahaa group
egypt
We are consultants in extraction ,analysis and trading the raw materials of mines as:-
Rock phosphate
32%-30%-28%-25%
Kaolin
Quartez-silica
Talcum
Feldspae(potash-sodumic)
Silica sand
Silica fume
Iron oxid ore
Manganese oxid
Cement(42.5%-32.5%)
Ferro manganese
Ferro manganese high carbon

 

water treatment unit design


 

وكلاء لشركات تركية وصينية لتوريد وتركيب وصيانة الغلايات وملحقاتها
solo agent for turkish and chinese companies for boiler production/manufacture/maintance

 

وكلاء لشركات تركية وصينية واوروبية لتصنيع وتركيب وصيانة ابراج التبريد المفتوحة

 

تصميم وتوريد وتركيب الشيللرات
design/production/maintance
chillers
ابراج التبريد المفتوحة
مجموعة تكنولاب البهاء جروب
المكتب الاستشارى العلمى
قطاع توريد خطوط انتاج المصانع
 
نحن طريقك لاختيار افضل خطوط الانتاج لمصنعكم
سابقة خبرتنا فى اختيار خطوط الانتاج لعملاؤنا
 
1)خطوط انتاج العصائر الطبيعية والمحفوظة والمربات
2)خطوط انتاج الزيوت الطبيعية والمحفوظة
3)خطوط انتاج اللبن الطبيعى والمحفوظ والمبستر والمجفف والبودرة
4)خطوط تعليب وتغليف الفاكهة والخضروات
5)خطوط انتاج المواسير البلاستيك والبى فى سى والبولى ايثيلين
6)خطوط انتاج التراى كالسيوم فوسفات والحبر الاسود
7)خطوط انتاج الاسفلت بانواعه
Coolمحطات معالجة الصرف الصناعى والصحى بالطرق البيولوجية والكيميائية
9)محطات معالجة وتنقية مياه الشرب
10)محطات ازالة ملوحة البحار لاستخدامها فى الشرب والرى
11)الغلايات وخطوط انتاج البخار الساخن المكثف
12)الشيللرات وابراج التبريد المفتوحة وخطوط انتاج البخار البارد المكثف
 
للاستعلام
مجموعة تكنولاب البهاء جروب
0117156569
0129834104
0163793775
 
القاهرة-شارع صلاح سالم-عمارات العبور-عمارة 17 ب
فلا تر رملية/كربونية/زلطيه/حديدية

وحدات سوفتنر لازالة عسر المياه

مواصفات مياه الشرب
Drinking water
acceptable
values

50

colour

acceptable

Taste

nil

Odour

6.5-9.2

ph

 

1 mg/dl

pb

5 mg/dl

as

50 mg/dl

cn

10 mg/dl

cd

0-100mg/dl

hg

8 mg/dl

f

45 mg/dl

N02

1 mg/dl

Fe

5 mg/dl

Mn

5.1 mg/dl

Cu

200 mg/dl

Ca

150 mg/dl

Mg

600 mg/dl

Cl

400 mg/dl

S04

200 mg/dl

Phenol

15 mg/dl

zn

 

 

الحدود المسموح به
ا لملوثات الصرف الصناعى
 بعد المعالجة
Acceptable
values
treated wate water
7-9.5

ph

25-37 c

Temp

40 mg/dl

Suspended solid

35 mg/dl

bod

3 mg/dl

Oil & grase

0.1 mg/dl

hg

0.02 mg/dl

cd

0.1 mg/dl

cn

0.5mg/dl

phenol

1.5 ds/m

conductivity

200 mg/dl

na

120 mg/dl

ca

56 mg/dl

mg

30 mg/dl

k

200 mg/dl

cl

150 mg/dl

S02

0.75 mg/dl

Fe

0.2 mg/dl

Zn

0.5 mg/dl

Cu

0.03 mg/dl

Ni

0.09 mg/dl

Cr

0.53 mg/dl

لb

0.15 mg/dl

pb

 





pipe flocculator+daf
plug flow flocculator
lamella settels

محطات تحلية مياه البحر بطريقة التقطير الومضى على مراحل
MSF+3.jpg (image)
محطات التقطير الومضى لتحلية مياه البحر2[MSF+3.jpg]
some of types of tanks we services
انواع الخزانات التى يتم تنظيفها
ASME Specification Tanks
Fuel Tanks
Storage Tanks
Custom Tanks
Plastic Tanks
Tank Cleaning Equipment
Double Wall Tanks
Septic Tanks
Water Storage Tanks
Fiberglass Reinforced Plastic Tanks
Stainless Steel Tanks
Custom / Septic
مراحل المعالجة الاولية والثانوية والمتقدمة للصرف الصناعى

صور مختلفة
من وحدات وخزانات معالجة الصرف الصناعى
 التى تم تصميمها وتركيبها من قبل المجموعة

صور
 من خزانات الترسيب الكيميائى والفيزيائى
 لوحدات معالجة الصرف الصناعى
المصممة من قبل المحموعة



technolab el-bahaa group


technolab el-bahaa group


technolab el-bahaa group

technolab el-bahaa group


technolab el-bahaa group


technolab el-bahaa group


technolab el-bahaa group


technolab el-bahaa group


technolab el-bahaa group


technolab el-bahaa group




مياه رادياتير اخضر اللون
بريستول تو ايه
انتاج شركة بريستول تو ايه - دمياط الجديدة
مجموعة تكنولاب البهاء جروب

اسطمبات عبوات منتجات شركة بريستول تو ايه-دمياط الجديدة

مياه رادياتير خضراء فوسفورية

من انتاج شركة بريستول تو ايه 

بترخيص من مجموعة تكنولاب البهاء جروب


زيت فرامل وباكم

DOT3



شاطر | 
 

 تعليمات تركيب الميسرات(السوفتنر)والمبادلات الايونية الحرارية(ايون اكسشينجر)

استعرض الموضوع السابق استعرض الموضوع التالي اذهب الى الأسفل 
كاتب الموضوعرسالة
Admin
Admin
avatar

عدد المساهمات : 3596
تاريخ التسجيل : 15/09/2009
العمر : 50
الموقع : مصر

مُساهمةموضوع: تعليمات تركيب الميسرات(السوفتنر)والمبادلات الايونية الحرارية(ايون اكسشينجر)   الأربعاء أكتوبر 05, 2011 12:35 pm

WATER SOFTENER ASSEMBLY INSTRUCTIONS
We think installing our softeners is very easy (if you are somewhat mechanically inclined and have a
little experience doing basic plumbing).

Note:

If you have an electric water heater we recommend that you turn off the electricity to the heater while
installing softener.

Once you are satisfied with the installation, turn on a few hot and coldwater faucets,
and let them run.

Once you are certain that there is no more air in your pipes, then turn the electricity
back on to the water heater.

Your kit should include:

Tall fiberglass mineral tank with distributor tube (or Turbulator tube, if ordered)
Box(es) of resin

Small box of gravel under bed (only on 2 cubic foot units)

Large funnel for pouring media into tank

Brine tank with 3/8” connecting tube

Autotrol control valve

Autotrol by-pass valve assembly

Tailpieces for valve – either copper or CPVC as specified

Autotrol Manual

Step 1:

Location of your softener is important. It should be in a level and non-freezing area (34-120 degrees F).

See manual for more details. The 2 tanks should be set close to each other.

The square tank with the
black lid is your brine tank (for softener salt or potassium chloride) and it is the tank that you will have to
refill sometimes, so make it the more accessible of the 2 tanks.

Do not put salt in this tank until you have
put the softener into service and have tested the cycles.

Step 2:

You will need a standard outlet that is not controlled by a switch, which can be 50 feet from your
softener.

Step 3:

You will need a drain for the backwashing cycles.

This should be no longer than 20 feet from the
softener. Refer to the Autotrol manual for exceptions and more details.

You will need to purchase this
flexible 1/2 i.d.

plastic pipe (can be vinyl, polyethylene polybutylene, etc. and same size will be used in
step 8).

This backwashing drain line will be under pressure when the backwash cycle is working. Make
sure the drain line is secured.

The drain line will need to drain into a drain, which should be a minimum
of 1 1/2” size, and ideally be below the top of the head of your softener.

Local codes should be adhered
to.

Note: Never connect the drain line directly into a drain.

Allow an air gap between the drain line and
waste line to prevent possibility of back- siphoning.

Step 4:

Once you have determined the exact location of your softener, it is time to fill the media/mineral tank
(taller of the 2) with the furnished media (looks like brown tiny beads and has a consistency of wet
sand).

The distributor tube should be in the mineral tank - screen intake would be at the bottom; open end will
be at the top.

The open end should be sticking 1 1/4" out of the mineral tank. The screen intake should
be resting on the bottom, centered.


There should be a plug in the open end of the distributor tube.

This is to keep any media from falling
into the distributor tube while pouring the media into the mineral tank.

Place the funnel (provided) into the mineral tank, and begin to put the resin into the mineral tank.

Be
careful to keep the distributor tube centered as best you can, while filling.

There should only be enough
resin to fill the tank about ½ to 2/3 full, but all the resin should be used.

The mineral tank should not be
filled to the top.

It is necessary for the media to have room to move during the backwash cycle.

An easy
(but slower) way to fill the mineral tank is to take a small scoop and pour the media into the funnel.

The
resin beads tend to stick to the funnel so by filling slowly the media will go into the tank easier. NOTE:

larger units will have a gravel underbed – pour this in before the resin.

Once the filling of the mineral tank is completed, carefully remove the plug from the distributor tube.

Do
not pull upwards on the distributor tube.
The control valve (head) now must be screwed onto the mineral tank (be sure the large O-ring is in
place).

As you start to screw the control valve onto the tank, make sure the hole in the center of the
control valve fits over the distributor tube. NO pipe dope or Teflon tape should be used on the threads.

The control valve should be hand tightened, snugly, clockwise.

Step 5:

You are now ready to install the bypass valve to the control valve.

Follow the instructions in the box.

The
in and out arrows on the bypass valve should be pointing the same direction as the in/out arrows on the
outside of the control valve.

The arrows are molded into the plastic on both the bypass valve and the
control valve.

Step 6:

Water connections to and from softener will now be connected to the bypass 1 1/4"IPS male threads by
using the two 1 1/4" Female nuts provided. Slip one 1 1/4" female nut over one of the flanged tailpieces,
so that the tube is sticking through the nut and the flanged piece is resting on the inside of the female
threaded part of the nut. Use one 1 3/4" o.d. rubber washer to fit into the female part of the nut on top
of the flanged tailpiece and screw the nut onto the 1 1/4" IPS male threads on the control valve.

Do the
same for the other side.

Step 7:

Between the valve and the brine tank you will need to connect the furnished 3/8” O.D. tubing.

One end
is to the fitting on the clear air check (255 valve only) or 3/8” fitting on the valve, and the other end
attaches to the elbow fitting inside the brine tank.

Pass the tubing through the hole and connect the


fitting entirely inside the brine tank. Do not use the fitting in the brine tank as a “bulkhead” fitting (i.e.
fastening the nut on the outside of the brine tank) – it must be connected entirely inside the brine
tank.

Hand tightening is all that should be needed.

Step 8:


Brine tank Overflow. Attach 1/2" i.d. plastic tubing to the fitting from the brine tank and run to a drain.


This drain line will not be under pressure.

DO NOT tie into the backwash drain line! This line should be
higher than your drain line.

Overflow drain line must be a separate line from fitting to the floor-drain,
sewer, tub, etc.

Now follow the instructions in the Autotrol manual for putting the softener into service.
NOTES ON SALT: Your brine tank will hold about 250 pounds of softer salt (about six 40-lb bags, or five
50-lb bags.

We recommend a high quality pellet-type salt – look for a low “insoluble” level (insoluble is a
nice word for dirt).

Potassium chloride salt substitute can be used as well, with no adjustments needed.
DO NOT ADD SALT UNTIL YOU HAVE COMPLETED THE SECTION ON PUTTING THE UNIT INTO SERVICE!

NOTES ON PROGRAMMING:

Logix 760 Controls –
To program the Logix control you simply need to enter in the amount of resin in cubic feet (see the Logix
Series Installer Quick-Start Sheet, Step 1).

The 32 Kgr units are 1.0 cubic foot, the 48 KGr are 1.5, and the
64 KGr are 2.0. In step 5, we recommend the Standard Salt (or “S”) setting for most applications.

460i Controls –
You will need to program three items into your Autotrol computer control: current time, capacity, and
water hardness.

You also need to set the salt dial to the proper setting (except Logix and 960).

Refer to
your manual for details.

When setting the capacity, you can take advantage of better salt efficiencies by setting them at a lower
capacity than the peak.

It will regenerate slightly more often, but the salt savings (up to 60% less salt)
make it worth it.

The chart in the Autotrol manual will show you the options.

One cubic foot (1.0 ft3) units have a peak capacity of 32,000 grains. We suggest that you program "24"
(for 24,000 grains) and the salt setting to 8.5.

One and a half cubic foot (1.5 ft3) units have a peak capacity of 48,000 grains. We suggest you program

the capacity to “35” and set the salt setting to 12 (set it at 6 on 460i units –they have the “XS” extra salt
cam which doubles the amount of salt – you need to cut the amount shown in the chart in half).

Two cubic foot (2.0 ft3) units have a peak capacity of 64,000 grains. We suggest you program the
capacity to “40” and set the salt setting to 12 (set it at 6 on 460i units –they have the “XS” extra salt cam
which doubles the amount of salt – you need to cut the amount shown in the chart in half).

If you do not know your hardness number, call your water department, or send us a water sample.

If
your water department gives you the hardness number in milligrams per liter (mg/l) or in parts per
million (ppm) you need to convert it to grains per gallon by dividing the number by 17.1.

Other Notes:

If using copper pipe, we recommend using type L copper.

Type L is thicker than type M copper.

Caution: A common problem for beginners when soldering onto the copper tailpieces is overheating
them, melting the plastic nuts that connect to the bypass valve.

We recommend that you wrap a wet rag
around the nuts and tailpieces to keep the heat away.

Also use care when tightening the tailpiece nuts
so you do not crack them!
Important: Be sure you double-check the inlet and outlet arrows on your softener before soldering!


Remember that your pipes and water heater contain hard water, so it will take a few days until your
water is 100% soft. Draining your water heater can hasten this.

This also will remove any build up
sediment (you are supposed to do this annually).

Remember to now not use as much soap for dishwashing, laundry, etc. etc.

No need for it! Many people
report needing to use only about 1/3 to 1/2 as much as they previously needed.

Remember to check with local code officials and install per local code.

by
technolab el-bahaa group
colonel.dr
bahaa badr
water treatment consultant
الرجوع الى أعلى الصفحة اذهب الى الأسفل
معاينة صفحة البيانات الشخصي للعضو http://technolabelbahaagp.googoolz.com
 
تعليمات تركيب الميسرات(السوفتنر)والمبادلات الايونية الحرارية(ايون اكسشينجر)
استعرض الموضوع السابق استعرض الموضوع التالي الرجوع الى أعلى الصفحة 
صفحة 1 من اصل 1

صلاحيات هذا المنتدى:لاتستطيع الرد على المواضيع في هذا المنتدى
مجموعة تكنولاب البهاء جروب :: قسم معالجة وتنقية وتحاليل المياه :: تصميم وتركيب وتوريد وحدات معالجة المياه-
انتقل الى: